Current Electricity MCQs for MDCAT (Physics) – 117 with Answers

Practise 117 MDCAT Physics MCQs on Current Electricity, arranged according to the PMDC MDCAT syllabus. This chapter covers electric current and Ohm's law, resistivity and its temperature dependence, series and parallel resistors, electrical power, emf and internal resistance, Kirchhoff's rules and the Wheatstone bridge.

Every question has an answer and a short explanation. Use practice mode for instant feedback, or take a timed test and review your answers at the end. Your progress is saved on this device. This page includes 10 new questions written by MDCAT City and 107 from our Physics question bank.

More chapters: all Physics MCQs, chapter by chapter.

Current electricity MCQs

Two 4 Ω resistors connected in parallel have an equivalent resistance of:

  1. 8 Ω
  2. 4 Ω
  3. 2 Ω
  4. 1 Ω

Answer: C

1/R = 1/4 + 1/4 = 1/2, so R = 2 Ω.

The resistance of a wire is directly proportional to its:

  1. Cross-sectional area
  2. Length
  3. Diameter squared
  4. Current

Answer: B

R = ρL/A: longer wires have more resistance; thicker wires have less.

Kirchhoff’s first (junction) law is based on conservation of:

  1. Energy
  2. Charge
  3. Momentum
  4. Mass

Answer: B

The current entering a junction equals the current leaving it.

A current of 2 A flows through a 5 Ω resistor. The power dissipated is:

  1. 10 W
  2. 20 W
  3. 2.5 W
  4. 50 W

Answer: B

P = I²R = 4 × 5 = 20 W.

A Wheatstone bridge with arms P, Q, R and S is balanced when:

  1. P + Q = R + S
  2. P/Q = R/S
  3. PQ = RS + 1
  4. P = Q = R = S only

Answer: B

At balance no current flows through the galvanometer and P/Q = R/S.

Ohm’s law applies when, for a conductor:

  1. Temperature and other physical conditions stay constant
  2. Current is very large
  3. Voltage is alternating
  4. The conductor is a semiconductor

Answer: A

V = IR holds for ohmic conductors at constant temperature.

The SI unit of resistivity is:

  1. Ω
  2. Ω m
  3. Ω m⁻¹
  4. S

Answer: B

ρ = RA/L, giving ohm-metres.

The resistance of a metal conductor generally:

  1. Decreases as temperature rises
  2. Increases as temperature rises
  3. Does not depend on temperature
  4. Becomes zero when heated

Answer: B

Ions vibrate more and impede electron flow.

An ammeter is connected in a circuit:

  1. In parallel and has high resistance
  2. In series and has very low resistance
  3. In parallel and has low resistance
  4. In series and has high resistance

Answer: B

It must carry the full current without changing it much.

A voltmeter is connected:

  1. In series with very low resistance
  2. In parallel with very high resistance
  3. In series with high resistance
  4. In parallel with low resistance

Answer: B

It should draw almost no current from the circuit.

Kirchhoff’s second (loop) law is based on conservation of:

  1. Charge
  2. Energy
  3. Momentum
  4. Mass

Answer: B

The sum of emfs equals the sum of potential drops around any closed loop.

The terminal voltage of a cell is less than its emf when current flows because of its:

  1. High temperature
  2. Internal resistance
  3. Low capacity
  4. Colour

Answer: B

V = ε − Ir, so some voltage is “lost” inside the cell.

A potentiometer is used to measure:

  1. Current accurately
  2. emf accurately without drawing current
  3. Resistance only
  4. Magnetic field

Answer: B

At the balance point no current is drawn from the cell being measured.

Conventional current flows in the external circuit from:

  1. Negative to positive terminal
  2. Positive to negative terminal
  3. Earth to the cell
  4. Nowhere

Answer: B

Electrons actually move the opposite way.

The drift velocity of electrons in a wire is:

  1. Close to the speed of light
  2. Very small, about millimetres per second
  3. Infinite
  4. Zero

Answer: B

Electrons drift slowly, but the electric signal travels very fast.

The resistance of an NTC thermistor, as temperature rises:

  1. Increases
  2. Decreases
  3. Stays the same
  4. Becomes infinite

Answer: B

More charge carriers become available when it is warmer.

The resistance of a light-dependent resistor (LDR) in bright light is:

  1. High
  2. Low
  3. Infinite
  4. Unchanged

Answer: B

Light releases more charge carriers.

The kilowatt-hour is a unit of:

  1. Power
  2. Energy
  3. Current
  4. Charge

Answer: B

It is the energy used by a 1 kW appliance in 1 hour.

A fuse protects a circuit by:

  1. Increasing current
  2. Melting and breaking the circuit when the current is too high
  3. Storing charge
  4. Changing AC to DC

Answer: B

It has a thin wire that melts at a set current.

The SI unit of electrical conductance is the:

  1. Ohm
  2. Siemens
  3. Henry
  4. Tesla

Answer: B

Conductance is the reciprocal of resistance.

PMC Practice Test If a conductor has a resistance of 50 Ω and a current of 5 A passes through it, what is the potential difference across it?

  1. 150 V
  2. 250 V
  3. 50 V
  4. 15 V

Answer: B

PMC Practice Test The electrical conductivity of metal sometimes decreases with the

  1. Increase in pressure
  2. Increase in temperature
  3. Decrease in temperature
  4. Decrease in pressure

Answer: B

PMC Practice Test The length of a conductor is halved. Its resistance will be:

  1. Halved
  2. Doubled
  3. Unchanged
  4. Quadrupled

Answer: A

PMC Practice Test Find the resistance if the voltage of a circuit is 45 V and the current is 30 A.

  1. 1.6 Ω
  2. 1.5 Ω
  3. 1.7 Ω
  4. 1.8 Ω

Answer: B

PMC Practice Test Relationship exists between current and voltage in terms of Ohm's law

  1. Non linear
  2. Varying
  3. Linear
  4. None of them

Answer: C

PMC Practice Test What is the power of a bulb operated at 220 V with a current of 1.5 A?

  1. 330 W
  2. 430 W
  3. 530 W
  4. 500 W

Answer: A

PMC Practice Test The terminal potential difference of a battery is greater than its emf when:

  1. The internal resistance of a battery is infinite
  2. The internal resistance of a battery is zero
  3. The battery is charged
  4. The battery is discharged

Answer: C

PMC Practice Test A galvanometer used as a voltmeter has:

  1. A high resistance in parallel
  2. A high resistance in series
  3. A low resistance in parallel
  4. A low resistance in series

Answer: B

PMC Practice Test A light bulb draws 300 mA when the voltage across it is 240 V. Its resistance is:

  1. 400 Ω
  2. 600 Ω
  3. 800 Ω
  4. 1000 Ω

Answer: C

PMC Practice Test Copper wire is used as connecting wire because:

  1. Copper has high electrical resistivity
  2. Copper has low electrical resistivity
  3. Copper has low electrical conductivity
  4. Copper has high value of elasticity

Answer: B

PMC Practice Test The value of current in a short circuit is ideally:

  1. Infinite
  2. Zero
  3. Minimum
  4. Maximum

Answer: A

PMC Practice Test An 8.0 V emf source is connected to a purely resistive appliance and a current of 2.0 A flows. The resistance of the appliance is:

  1. 4 Ω
  2. 6 Ω
  3. 2 Ω
  4. 3 Ω

Answer: A

PMC Practice Test A battery has emf E = 10 V and terminal voltage V = 9 V when a current of 1 A flows. Its internal resistance is:

  1. 1 Ω
  2. 0.1 Ω
  3. 0.01 Ω
  4. None of these

Answer: A

PMC Practice Test An example of a non-ohmic device is a:

  1. Diode
  2. Tungsten wire
  3. Carbon resistance
  4. Copper wire

Answer: A

PMC Practice Test Two incandescent bulbs rated 40 W and 60 W are connected in series across the mains. Then:

  1. The bulbs together consume 100 W
  2. The bulbs together consume 50 W
  3. The 60 W bulb glows brighter
  4. The 40 W bulb glows brighter

Answer: D

PMC Practice Test Electric current may be defined as

  1. Rate of flow of charge
  2. Rate of flow of momentum
  3. Rate of flow of power
  4. None of them

Answer: A

PMC Practice Test Volt/ampere is equal to:

  1. Ohm
  2. Ohm meter
  3. Pascal
  4. None of them

Answer: A

PMC Practice Test The specific resistance (resistivity) of a conductor increases with:

  1. Increase in temperature
  2. Increase in cross-sectional area
  3. Decrease in length
  4. Decrease in cross-sectional area

Answer: A

PMC Practice Test A charge of 4000 C passes through a wire in 12 seconds. The current is about:

  1. 333.3 A
  2. 333.3 V
  3. 666.7 A
  4. None of these

Answer: A

PMC Practice Test In a parallel circuit, the voltage across each branch remains:

  1. Same
  2. Different
  3. Both of them
  4. None of them

Answer: A

PMC Practice Test Resistivity of a conductor depends upon

  1. Temperature
  2. Length
  3. Cross sectional area
  4. None of these

Answer: A

PMC Practice Test The fractional change in resistance per kelvin is known as the:

  1. Coefficient in resistance
  2. Temperature coefficient of resistance
  3. Resistance
  4. None of these

Answer: B

PMC Practice Test If a current of 1 A flows through a conductor for 1 hour, the charge that flows is:

  1. 5 C
  2. 18000 C
  3. 1 C
  4. 3600 C

Answer: D

PMC Practice Test Maximum power is delivered to a load when the internal resistance of the source equals the:

  1. Zero resistance
  2. Load resistance
  3. Max resistance
  4. None of these

Answer: B

PMC Practice Test 1/R(eq) = 1/R₁ + 1/R₂ + … + 1/Rₙ applies to resistors connected in:

  1. Series
  2. Parallel
  3. Both of them
  4. None of them

Answer: B

PMC Practice Test A steady current does not change with respect to:

  1. Conductor
  2. Source
  3. Time
  4. Potential difference

Answer: C

PMC Practice Test Four 40 W bulbs are connected in series across a battery. Which statement is true?

  1. The current through each bulb in same
  2. The voltage across each bulb is not same
  3. The power dissipation in each bulb is not same
  4. None of the above

Answer: A

PMC Practice Test Basically a potentiometer is a device for

  1. Comparing two voltages
  2. Measuring a current
  3. Comparing two currents
  4. Measuring a voltage

Answer: A

PMC Practice Test One kilo-ohm is equal to:

  1. 10³ Ω
  2. 10² Ω
  3. 10⁴ Ω
  4. None of these

Answer: A

PMC Practice Test Which one of the following bulbs has the least resistance?

  1. 100W
  2. 200W
  3. 300W
  4. 60w

Answer: C

PMC Practice Test A wire has a resistance of 5.5 Ω at 19 °C and 21.5 Ω at 200 °C. Its temperature coefficient of resistance is about:

  1. 0.016 per °C
  2. 32 per °C
  3. 0.018 per °C
  4. 0.00106 per °C

Answer: A

PMC Practice Test Ohm's law is NOT applicable to:

  1. Semiconductors
  2. D.C. circuits
  3. Small resistors
  4. High currents

Answer: A

PMC Practice Test R(eq) = R₁ + R₂ + R₃ + … + Rₙ applies to resistors connected in:

  1. Series
  2. Parallel
  3. Both of them
  4. None of them

Answer: A

PMC Practice Test If E = 10 V, the terminal voltage is 9 V and I = 1 A, the internal resistance of the battery is:

  1. 1 Ω
  2. 0.1 Ω
  3. 0.01 Ω
  4. None of these

Answer: A

PMC Practice Test Resistivity of a substance is the resistance of a ___ of that substance.

  1. Metre length
  2. Square metre
  3. Metre cube
  4. Centimetre

Answer: C

PMC Practice Test The hot resistance of a bulb filament is higher than its cold resistance because its temperature coefficient of resistance is:

  1. Zero
  2. Negative
  3. Positive
  4. About 2 ohms per degree

Answer: C

PMC Practice Test Ohm's law holds for:

  1. Metallic conductors at low temperature
  2. Metallic conductors at high temperature
  3. For electrolytes, when current passes through them
  4. For diode when current flows

Answer: A

PMC Practice Test Four wires of same material, the same cross-sectional area and the same length when connected in parallel give a resistance of 0.25 ohms. If the same four wires are connected is series the effective resistance will be

  1. 1ohm
  2. 2o0hm
  3. 3 ohm
  4. 4ohm

Answer: D

PMC Practice Test Electric power is

  1. Rate of electric work done per unit time
  2. Voltage per unit time
  3. Electric charge per unit time
  4. Current per unit time

Answer: A

PMC Practice Test Electrical power is given by P =

  1. VI
  2. I²R
  3. V²/R
  4. All of these

Answer: D

PMC Practice Test A wire of uniform area of cross-section A and length L is cut into two equal parts, the resistivity of each partis

  1. Doubled
  2. Half
  3. Remains the same
  4. Increase three times

Answer: C

PMC Practice Test If I, R and t are current, resistance and time, Joule's law gives the heat produced as:

  1. I²Rt
  2. I²R/t
  3. I²R²t
  4. I²R²t²

Answer: A

PMC Practice Test An apparatus which is used to measure current voltage and resistance

  1. Multimeter
  2. Ammeter
  3. Galvanometer
  4. Voltmeter

Answer: A

PMC Practice Test How much potential difference is required for establishing steady current?

  1. Minimum
  2. Constant
  3. Maximum
  4. Varying

Answer: B

PMC Practice Test Specific resistance of all metals is mostly affected by

  1. Temperature
  2. Pressure
  3. Magnetic field
  4. Volume

Answer: A

PMC Practice Test How much charge passes through a circuit if a current of 10 A flows for 15 s?

  1. 1500 Coulomb
  2. 150 Coulomb
  3. 13400 Coulomb
  4. 140 Coulomb

Answer: B

PMC Practice Test A potential difference of 10 V is applied across a conductor of resistance 2.5 Ω. The current is:

  1. 4A
  2. 2A
  3. 6A
  4. 10A

Answer: A

PMC Practice Test The condition for the validity of Ohm's law is that the

  1. Temperature should remain constant
  2. Current should be proportional to voltage
  3. Resistance must be wire wound type
  4. All of the above

Answer: A

PMC Practice Test Ohm’s law is valid when the temperature of conductor is :

  1. Very low
  2. Very high
  3. Varying
  4. Constant

Answer: D

PMC Practice Test The relationship between power, current and resistance is:

  1. P = I²R
  2. P = I²R/2
  3. P = IR
  4. All of them

Answer: A

PMC Practice Test What is the SI unit of emf?

  1. Ohm
  2. Ampere
  3. Volt
  4. Newton

Answer: C

PMC Practice Test Reciprocal of resistivity is called

  1. Resistance
  2. Inductance
  3. Conductivity
  4. Flexibility

Answer: C

PMC Practice Test The resistance of a conductor at absolute zero (0 K) is

  1. Almost zero
  2. Almost infinite
  3. No prediction at all
  4. May increase or decrease

Answer: A

PMC Practice Test In series circuit, current remains?

  1. Same
  2. Different
  3. Sometimes same sometimes different
  4. None of them

Answer: A

PMC Practice Test Coulomb per second is equivalent to

  1. Ampere
  2. Farad
  3. Henry
  4. Watt

Answer: A

PMC Practice Test A potentiometer is used to measure the emf of a cell. At null point, no current flows through

  1. The main circuit
  2. The cell circuit
  3. Both the main and cell circuits
  4. The potentiometer wire

Answer: B

PMC Practice Test The temperature coefficient of resistance is expressed in:

  1. °C
  2. °C⁻¹
  3. M °C⁻¹
  4. None of these

Answer: B

PMC Practice Test Resistance of carbon filament lamp as the applied voltage increases.

  1. Increases
  2. Decreases
  3. Remains same
  4. None of the above

Answer: B

PMC Practice Test The SI Unit for resistance is?

  1. Ohm
  2. Ampere
  3. Watt
  4. Volts

Answer: A

PMC Practice Test An electrical instrument which is used to measure potential difference between two points is called

  1. Barometer
  2. Manometer
  3. Galvanometer
  4. Voltmeter

Answer: D

PMC Practice Test Which of the following can have a negative temperature coefficient of resistance?

  1. Compounds of silver
  2. Liquid metals
  3. Metallic alloys
  4. Electrolytes

Answer: D

PMC Practice Test The international ohm is defined in terms of the resistance of a:

  1. Column of mercury
  2. Cube of carbon
  3. Cube of copper
  4. Unit length of wire

Answer: A

PMC Practice Test Internal resistance is the resistance offered by

  1. Source of emf
  2. Conductor
  3. Resistor
  4. Capacitor

Answer: A

PMC Practice Test There are three bulbs of 60 W, 100 W and 200 W (same voltage). Which bulb has the thickest filament?

  1. 100 W
  2. 200 W
  3. 60 W
  4. All the same

Answer: B

PMC Practice Test A current of 5 A flows in a 2 Ω resistor. The energy dissipated in 300 s is:

  1. 5 kJ
  2. 10 kJ
  3. 15 kJ
  4. 20 kJ

Answer: C

PMC Practice Test When the length of a conductor is doubled and its cross-sectional area remains the same, its resistance:

  1. Remains the same
  2. Will be doubled
  3. Will become half
  4. Will increase by four times

Answer: B

PMC Practice Test If the length of a potentiometer wire is doubled, the accuracy in determining the null point:

  1. Is increased
  2. Is decreased
  3. Remains constant
  4. May increase or decrease

Answer: A

PMC Practice Test The energy used by a 20 Ω resistor carrying 5 A for 3 hours is:

  1. 1 kWh
  2. 1.5 kWh
  3. 2 kWh
  4. 3 kWh

Answer: B

PMC Practice Test All of the following are equivalent to the watt EXCEPT:

  1. (ampere)² × ohm
  2. Joule/second
  3. Ampere × volt
  4. Ampere/volt

Answer: D

PMC Practice Test A total charge of 5000 C passes through a circuit carrying a current of 20 A. The time taken is:

  1. 250 seconds
  2. 350 seconds
  3. 400 seconds
  4. 500 seconds

Answer: A

PMC Practice Test As compared to thin wires, thick wires have

  1. More resistance
  2. No resistance
  3. Less resistance
  4. Same resistance

Answer: C

PMC Practice Test Which of the following has a negative temperature coefficient of resistance?

  1. Tungsten
  2. Carbon
  3. Nichrome
  4. Platinum

Answer: B

PMC Practice Test Terminal potential difference of a cell

  1. Increases with increase in its internal resistance
  2. Decrease with increase in intemal resistance
  3. Is independent of its internal resistance
  4. None of these

Answer: B

PMC Practice Test Ohm's law is valid at temperatures

  1. Constant
  2. Varying
  3. All of them
  4. None of them

Answer: A

PMC Practice Test The sensitivity of a potentiometer can be increased by:

  1. Increasing the e.m-f. of the primary cell
  2. Increasing the potential gradient
  3. Increasing the length of the potentiometer wire
  4. Decreasing the length of the potentiometer wire

Answer: C

PMC Practice Test The emf equals the terminal potential difference when the:

  1. Circuit is closed
  2. Current is max
  3. Circuit is open
  4. All of these

Answer: C

PMC Practice Test A current of 16 A divides between two parallel branches of 8 Ω and 12 Ω. The currents in the 12 Ω and 8 Ω branches are:

  1. 6.4 A, 6.9 A
  2. 6.4 A, 9.6 A
  3. 4.6 A, 6.9 A
  4. 4.6 A, 9.6 A

Answer: B

PMC Practice Test If 6 C of charge flows through a conductor in 2 s, the current is:

  1. 3 ampere
  2. 3 volts
  3. 2 amperes
  4. 2 volts

Answer: A

PMC Practice Test The specific resistance (resistivity) of a copper rod compared with that of a thin copper wire is:

  1. Less
  2. More
  3. Same
  4. Depends upon the length and area of cross-section of the wire

Answer: C

PMC Practice Test A 40 Ω resistance carries a current of 300 A. The voltage across it is:

  1. 12000 volts
  2. 15000 volts
  3. 20000 volts
  4. 300 volts

Answer: A

PMC Practice Test The resistance of a superconductor is

  1. Finite
  2. Infinite
  3. Zero
  4. Changes with every conductor

Answer: C

PMC Practice Test EMF stands for

  1. Electromotive force
  2. Electrical momentum force
  3. Electric Magnetic force
  4. None of them

Answer: A

PMC Practice Test If a current of 5 A flows through a conductor, the number of electrons passing per second is:

  1. 1.6 × 10⁻¹⁹
  2. 3.12 × 10¹⁹
  3. 4 × 10¹⁹
  4. 7.68 × 10²⁰

Answer: B

PMC Practice Test The graph of Ohm's law (V against I) is a:

  1. Hyperbola
  2. Ellipse
  3. Parabola
  4. Straight line

Answer: D

PMC Practice Test The SI unit of current is the:

  1. Ampere
  2. Volt
  3. Joules
  4. Watt

Answer: A

PMC Practice Test The resistance and length of a wire (same material and area) are:

  1. Inversely related
  2. Directly related
  3. Not related
  4. Inversely proportional

Answer: B

PMC Practice Test A 200 W bulb operates on a 220 V supply. The current is:

  1. 0.9 A
  2. 0.6 A
  3. 2 A
  4. 3 A

Answer: A

Ohm's law can be written as:

  1. V = R/I
  2. V = I/R
  3. V = I²R
  4. V = IR

Answer: D

At constant temperature, the current through a conductor is proportional to the voltage across it.

Three 6 Ω resistors connected in parallel have an equivalent resistance of:

  1. 18 Ω
  2. 2 Ω
  3. 3 Ω
  4. 6 Ω

Answer: B

1/R = 1/6 + 1/6 + 1/6 = 1/2, so R = 2 Ω.

The resistance of a uniform wire is directly proportional to its:

  1. Cross-sectional area
  2. Length
  3. Diameter
  4. Thickness

Answer: B

R = ρL/A.

If a wire is stretched to double its length (volume constant), its resistance becomes:

  1. Four times
  2. Half
  3. Unchanged
  4. Double

Answer: A

Length doubles and area halves, so R = ρL/A increases by 2 × 2 = 4 times.

Kirchhoff's first (junction) rule is based on conservation of:

  1. Energy
  2. Mass
  3. Momentum
  4. Charge

Answer: D

The total current entering a junction equals the total current leaving it.

Kirchhoff's second (loop) rule is based on conservation of:

  1. Momentum
  2. Current
  3. Charge
  4. Energy

Answer: D

The sum of emfs equals the sum of potential drops around any closed loop.

The power dissipated in a resistor R carrying a current I is:

  1. I²R
  2. IR
  3. V/I
  4. I/R

Answer: A

P = VI = I²R = V²/R.

An ideal voltmeter should have:

  1. Resistance equal to the circuit's
  2. Low resistance
  3. Infinite resistance
  4. Zero resistance

Answer: C

It must not draw current from the circuit it measures.

A Wheatstone bridge is used to measure an unknown:

  1. Voltage only
  2. Resistance
  3. Current
  4. Capacitance

Answer: B

At balance, P/Q = R/S gives the unknown resistance.

The resistance of a metal conductor increases with temperature because:

  1. Lattice vibrations increase and electrons collide more often
  2. Electrons slow down at room temperature
  3. The charge on the electron increases
  4. The number of free electrons decreases

Answer: A

Stronger vibrations of the ions scatter the drifting electrons more.

Contact Form