Electromagnetic Induction MCQs for MDCAT (Physics) – 91 with Answers

Practise 91 MDCAT Physics MCQs on Electromagnetic Induction, arranged according to the PMDC MDCAT syllabus. This chapter covers magnetic flux, Faraday's and Lenz's laws, motional emf, self and mutual induction, the AC generator, the DC motor and back emf, and transformers.

Every question has an answer and a short explanation. Use practice mode for instant feedback, or take a timed test and review your answers at the end. Your progress is saved on this device. This page includes 10 new questions written by MDCAT City and 81 from our Physics question bank.

More chapters: all Physics MCQs, chapter by chapter.

Electromagnetic induction MCQs

Faraday’s law states that the induced emf is proportional to the:

  1. Magnetic flux
  2. Rate of change of magnetic flux
  3. Current
  4. Resistance

Answer: B

ε = −N dΦ/dt.

Lenz’s law is a consequence of conservation of:

  1. Charge
  2. Momentum
  3. Energy
  4. Mass

Answer: C

The induced current opposes the change causing it; otherwise energy would be created from nothing.

A transformer works on the principle of:

  1. Self-induction
  2. Mutual induction
  3. Electrostatic induction
  4. Thermionic emission

Answer: B

A changing current in the primary coil induces an emf in the secondary coil.

In a step-up transformer:

  1. Nₛ < Nₚ
  2. Nₛ > Nₚ
  3. Nₛ = Nₚ
  4. There is no secondary coil

Answer: B

More turns on the secondary coil give a higher output voltage.

The SI unit of inductance is the:

  1. Farad
  2. Henry
  3. Weber
  4. Ohm

Answer: B

1 henry = 1 V s A⁻¹.

An AC generator converts:

  1. Electrical energy into mechanical energy
  2. Mechanical energy into electrical energy
  3. Heat into light
  4. Chemical energy into heat

Answer: B

A rotating coil in a magnetic field has an emf induced in it.

Eddy-current losses in a transformer core are reduced by:

  1. Using a solid iron core
  2. Using a laminated core
  3. Increasing current
  4. Removing the core

Answer: B

Thin insulated layers break up the eddy-current paths.

A rod of length L moves with speed v at right angles to a magnetic field B. The induced emf is:

  1. BL/v
  2. BLv
  3. Bv/L
  4. B/Lv

Answer: B

This is motional emf, ε = BLv.

The back emf in an electric motor:

  1. Adds to the applied voltage
  2. Opposes the applied voltage
  3. Is always zero
  4. Only exists in generators

Answer: B

It increases as the motor speeds up, limiting the current.

A transformer does not work on steady DC because:

  1. DC is too strong
  2. There is no changing magnetic flux
  3. The coils melt
  4. DC has no voltage

Answer: B

Induction needs a changing flux in the core.

If a magnet is held still inside a coil, the induced current is:

  1. Maximum
  2. Zero
  3. Alternating
  4. Steady and large

Answer: B

An emf is induced only when the flux changes.

Fleming’s right-hand rule gives the direction of the:

  1. Force on a motor
  2. Induced current in a moving conductor
  3. Electric field
  4. Torque

Answer: B

It is used for generators.

The energy stored in an inductor carrying current I is:

  1. LI
  2. ½LI²
  3. LI²
  4. ½L²I

Answer: B

L is the inductance.

Power is transmitted over long distances at very high voltage to:

  1. Make it more dangerous
  2. Reduce the current and so reduce I²R losses
  3. Increase the frequency
  4. Increase resistance

Answer: B

For the same power, higher voltage means lower current.

A DC generator uses a split-ring commutator to:

  1. Increase the voltage
  2. Make the output current flow in one direction
  3. Reduce friction
  4. Cool the coil

Answer: B

It reverses the coil connections every half turn.

PMC Practice Test Which of the following remains unchanged in transformer

  1. Voltage
  2. Current
  3. Power
  4. Capacitance

Answer: C

PMC Practice Test For a 1 efficient step down transformer

  1. Voltage in primary and secondary are equal
  2. Current in primary and secondary are equal
  3. Input power is same as the output power
  4. Output power is zero

Answer: C

PMC Practice Test A transformer steps down 200 V to 50 V. If the secondary has 40 turns, the primary has:

  1. 150 turns
  2. 160 turns
  3. 170 turns
  4. 200 turns

Answer: B

PMC Practice Test The self-inductance of a coil varies with its number of turns N as:

  1. N
  2. N³
  3. N²
  4. 1/N

Answer: C

PMC Practice Test A metal rod 4 m long moves at 5 m/s perpendicular to a 0.5 T magnetic field. The induced emf is:

  1. 10 V
  2. 20 V
  3. 30 V
  4. 4 V

Answer: A

PMC Practice Test The energy stored in an inductor is:

  1. Electric energy
  2. Magnetic energy
  3. Electromagnetic energy
  4. Both a) and b)

Answer: B

PMC Practice Test In an AC generator, the rectangular coil of many turns of copper wire wound on a soft iron core is called the:

  1. Slip rings
  2. Armature
  3. Copper brushes
  4. Field magnet

Answer: B

PMC Practice Test In a battery eliminator, the 220 V mains supply is stepped down to 11 V. What is the transformation ratio (primary: secondary)?

  1. 1:20
  2. 20:1
  3. 1:2
  4. 2:5

Answer: B

PMC Practice Test The mutual induction happens in

  1. AC generator
  2. DC generator
  3. Battery
  4. Transformer

Answer: D

PMC Practice Test In step up transformer is increased in secondary coils

  1. Electric field
  2. Magnetic field
  3. Number of turns
  4. None of these

Answer: C

PMC Practice Test The insulation between sheets of transformer core is to get small

  1. Hysteresis loop
  2. Eddy current
  3. Both
  4. None of these

Answer: B

PMC Practice Test "The direction of the induced current is always such as to oppose the change causing it." This is:

  1. Faraday's Law
  2. Lenz's Law
  3. Ohm's Law
  4. Kirchoff'’s Law

Answer: B

PMC Practice Test Which of the following is NOT present in an AC generator?

  1. Armature
  2. Magnet
  3. Slip rings
  4. Commutator

Answer: D

PMC Practice Test In rectification, a transformer is used to ___ the supply voltage.

  1. Step up
  2. Step down
  3. Equalize
  4. None of them

Answer: B

PMC Practice Test The secondary of which transformer must always be kept closed (shorted through the meter)?

  1. Power
  2. Voltage
  3. Current
  4. Step down

Answer: C

PMC Practice Test A transformer has negative voltage regulation when its load power factor is:

  1. Lagging
  2. Leading
  3. Unity
  4. Any of above

Answer: B

PMC Practice Test The SI unit of inductance is the:

  1. Henry
  2. Farad
  3. Maxwell
  4. Weber

Answer: A

PMC Practice Test Harmonics in a transformer result in:

  1. Increases core loss
  2. Increases I²R loss
  3. Interference with communication circuits
  4. All of the above

Answer: D

PMC Practice Test A breather is provided in a transformer to:

  1. Absorb moisture of air during breathing
  2. Provide cold air in the transformer
  3. The filter of transformer oil
  4. None of above

Answer: A

PMC Practice Test The henry is the unit of:

  1. Self inductance only
  2. Mutual inductance
  3. Both a) and b)
  4. Emf

Answer: C

PMC Practice Test Mutual inductance does NOT depend on:

  1. Relative orientation
  2. Relative separation of two coils
  3. Reciprocity
  4. Permeability of the core material

Answer: C

PMC Practice Test The emf produced in an AC generator is:

  1. NωAB cos ωt
  2. NωAB tan ωt
  3. NωAB cot ωt
  4. NωAB sin ωt

Answer: D

PMC Practice Test Core of transformer is made up of

  1. Copper
  2. Aluminum
  3. Iron
  4. Steel

Answer: C

PMC Practice Test Whenever the magnetic flux linked with an electric circuit changes, an emf is induced in the circuit. This is called

  1. Electromagnetic induction
  2. Kirchoff's law
  3. Hysteresis loss
  4. Lenz's law

Answer: A

PMC Practice Test If we make the magnetic field stronger, the value of induced current is

  1. Decreased
  2. Increased
  3. Vanished
  4. Kept constant

Answer: B

PMC Practice Test The energy stored in an inductor is given by:

  1. ½LI²
  2. LI²
  3. (3/2)LI²
  4. LI

Answer: A

PMC Practice Test Principle of electric generator is based on

  1. Biot savart’s law
  2. Ampere’s law
  3. Newton’'s law
  4. Faraday law

Answer: D

PMC Practice Test Which one of the following is not found in a DC generator?

  1. Armature
  2. Slip rings
  3. Commutators
  4. Magnets

Answer: B

PMC Practice Test Lenz's law is in accordance with the conservation of:

  1. Momentum
  2. Charge
  3. Current
  4. Energy

Answer: D

PMC Practice Test If the rate of change of flux through a coil is doubled, the induced (motional) emf:

  1. Halves
  2. Triples
  3. Doubles
  4. Remains unchanged

Answer: C

PMC Practice Test In order to enhance magnetic flux, the primary and secondary coils of the transformer are wound on

  1. Soft iron core
  2. Iron core
  3. Hard iron core
  4. Steel core

Answer: A

PMC Practice Test Which of the following losses in a transformer is zero even at full load

  1. Eddy current loss
  2. Core loss
  3. Copper loss
  4. Friction loss

Answer: D

PMC Practice Test Primary and secondary powers of a transformer are 200W and 100 W respectively, the efficiency of a transformer is

  1. 50%
  2. 1
  3. 20%
  4. 10%

Answer: A

PMC Practice Test In step down transformer is decreased in secondary coils

  1. Electric field
  2. Magnetic field
  3. Number of turns
  4. None of these

Answer: C

PMC Practice Test Voltage in secondary winding is to current in secondary coil

  1. Directly proportional
  2. Inversely proportional
  3. Directly squared proportional
  4. Not enough information

Answer: B

PMC Practice Test An electric motor converts ___ energy into ___ energy.

  1. Electrical, mechanical
  2. Mechanical, electrical
  3. Mechanical, potential
  4. Not enough information

Answer: A

PMC Practice Test Time varying magnetic field creates electric field, this is called

  1. Electric induction
  2. Magnetic induction
  3. Electromagnetic induction
  4. Dipole induction

Answer: C

PMC Practice Test Faraday law states that the rate of change of magnetic flux is equal to

  1. Electromotive force
  2. Induced current
  3. Induced flux
  4. Induced magnetic field

Answer: A

PMC Practice Test Electric generator converts to energy

  1. Electric, mechanical
  2. Mechanical, electric
  3. Mechanical , potential
  4. Not enough information

Answer: B

PMC Practice Test For an ideal step-up transformer, the secondary power is ___ the primary power.

  1. Equal to
  2. Greater than
  3. Less than
  4. None of these

Answer: A

PMC Practice Test According to Faraday's law, the emf induced in a circuit depends on the:

  1. Max. magnetic flux
  2. Rate of change of magnetic flux
  3. Change in magnetic flux
  4. Initial flux

Answer: B

PMC Practice Test The core of transformer is made up of

  1. Hard iron
  2. Soft iron
  3. Aluminium
  4. Copper

Answer: B

PMC Practice Test A step-down transformer has ___ turns in its secondary coil.

  1. More
  2. Less
  3. Equal
  4. Zero

Answer: B

PMC Practice Test Motional emf induced in a coil is dependent on

  1. Magnetic field
  2. Orientation
  3. Length
  4. All of these

Answer: D

PMC Practice Test The coupling coefficient of a perfectly coupled coil is:

  1. 0
  2. 1
  3. More than 1
  4. Infinite

Answer: B

PMC Practice Test The role of inductance is equivalent to:

  1. Inertia
  2. Force
  3. Energy
  4. Momentum

Answer: A

PMC Practice Test Which of the following is a unit of mutual inductance?

  1. V s A⁻²
  2. V A s²
  3. V² s
  4. V s A⁻¹

Answer: D

PMC Practice Test According to Faraday law induced voltage is produced by change in

  1. Electric field
  2. Magnetic field
  3. Both a orb
  4. Position

Answer: B

PMC Practice Test A transformer lights a 100 W, 25 V lamp from 250 V AC mains. The current in the mains cable is 0.5 A. The efficiency is:

  1. 50%
  2. 60%
  3. 90%
  4. 80%

Answer: D

PMC Practice Test The maximum emf generated in an AC generator is:

  1. ε₀ = NωAB sin θ
  2. ε₀ = sin θ
  3. ε = 0 sin θ
  4. ε₀ = NωAB

Answer: D

PMC Practice Test The motional emf induced in a coil is independent of the:

  1. Number of turns
  2. Change in flux
  3. Change in time
  4. Resistance

Answer: D

PMC Practice Test Principle of transformer is

  1. Mutual inductance
  2. Self induction
  3. Motional emf
  4. None of these

Answer: A

PMC Practice Test Lamination of the transformer core is made of

  1. Cast iron
  2. Silicon steel
  3. Aluminium
  4. Cast steel

Answer: B

PMC Practice Test One of the major reasons for heat loss in transformer is

  1. Radiation loss
  2. Convection loss
  3. Eddy current loss
  4. None of these

Answer: C

PMC Practice Test In an AC generator, increasing the number of turns in the coil:

  1. Increases emf
  2. Decreases emf
  3. Makes the emf zero
  4. Maintains the emf at a constant value

Answer: A

PMC Practice Test Mutual inductance plays a practical role in the working of a:

  1. AC generator
  2. Radio choke
  3. DC generator
  4. Transformer

Answer: D

PMC Practice Test Emf = −N(ΔΦ/Δt) is according to:

  1. Ampere's Law
  2. Faraday's Law
  3. Lenz's Law
  4. None of these

Answer: B

PMC Practice Test For a coil of self-inductance L carrying current I, the flux linkage is:

  1. LI
  2. LI²
  3. L²I
  4. L²

Answer: A

PMC Practice Test The turns ratio (Ns/Np) of a transformer is 10. This means:

  1. Is = 10 Ip
  2. Ns = Np/10
  3. Ns = 10 Np
  4. Vs = Vp/10

Answer: C

PMC Practice Test A device that consumes electrical energy in the external circuit of a generator is called the:

  1. Appliances
  2. Machines
  3. Motors
  4. Load

Answer: D

PMC Practice Test When Ns > Np, the transformer is:

  1. Step up
  2. Step down
  3. Primary
  4. Secondary

Answer: A

PMC Practice Test Lenz's law gives the direction of the:

  1. Inductance
  2. Induced current
  3. Induced flux
  4. Induced magnetic field

Answer: B

PMC Practice Test A transformer is based on the principle of:

  1. Self inductance only
  2. Mutual inductance
  3. Capacitive effect
  4. All of these

Answer: B

PMC Practice Test A transformer operates on:

  1. A.C
  2. D.C
  3. Both
  4. None of these

Answer: A

PMC Practice Test Alternating current generators use:

  1. Coiled rings
  2. Split rings
  3. Slip rings
  4. Solenoid rings

Answer: C

PMC Practice Test The principle of a DC generator is based on:

  1. Coulomb's Law
  2. Ampere's Law
  3. Faraday's Law
  4. Lenz's Law

Answer: C

According to Faraday's law, the induced emf equals the rate of change of:

  1. Magnetic flux linkage
  2. Current
  3. Resistance
  4. Charge

Answer: A

ε = −N ΔΦ/Δt.

Lenz's law is a consequence of the law of conservation of:

  1. Charge
  2. Momentum
  3. Energy
  4. Mass

Answer: C

The induced current opposes the change that causes it, so energy must be supplied.

The SI unit of magnetic flux is the:

  1. Weber
  2. Tesla
  3. Farad
  4. Henry

Answer: A

1 Wb = 1 T m².

The SI unit of self-inductance is the:

  1. Henry
  2. Tesla
  3. Weber
  4. Ohm

Answer: A

1 H = 1 V s A⁻¹.

A transformer works on the principle of:

  1. Self-induction only
  2. Mutual induction
  3. Electrostatic induction
  4. The photoelectric effect

Answer: B

A changing current in the primary induces an emf in the secondary.

A transformer cannot be used with:

  1. DC
  2. High-voltage AC
  3. AC
  4. Low-voltage AC

Answer: A

Steady DC produces no changing flux, so no emf is induced.

In a step-up transformer, the number of turns in the secondary coil is:

  1. Zero
  2. More than in the primary
  3. Less than in the primary
  4. Equal to the primary

Answer: B

Vs/Vp = Ns/Np, so more secondary turns give a higher voltage.

Eddy current losses in a transformer are reduced by using a:

  1. Wooden core
  2. Solid iron core
  3. Laminated iron core
  4. Copper core

Answer: C

Thin insulated sheets break up the paths of the eddy currents.

An AC generator converts:

  1. Heat into electrical energy
  2. Light into electrical energy
  3. Electrical energy into mechanical energy
  4. Mechanical energy into electrical energy

Answer: D

A coil rotated in a magnetic field produces an alternating emf.

The motional emf in a rod of length L moving with velocity v perpendicular to a field B is:

  1. BL / v
  2. B / Lv
  3. Bv / L
  4. BLv

Answer: D

ε = BLv.

Contact Form