Solids and Electronics MCQs for MDCAT (Physics) – 73 with Answers

Practise 73 MDCAT Physics MCQs on Solids and Electronics, arranged according to the PMDC MDCAT syllabus. This chapter covers stress, strain and Young's modulus, elastic and plastic behaviour, energy bands in conductors, insulators and semiconductors, p- and n-type semiconductors, the p-n junction diode and rectification, transistors and logic gates.

Every question has an answer and a short explanation. Use practice mode for instant feedback, or take a timed test and review your answers at the end. Your progress is saved on this device. This page includes 15 new questions written by MDCAT City and 58 from our Physics question bank.

More chapters: all Physics MCQs, chapter by chapter.

Physics of solids and electronics MCQs

A semiconductor doped with a pentavalent impurity becomes:

  1. p-type
  2. n-type
  3. An insulator
  4. A superconductor

Answer: B

The fifth valence electron of the impurity becomes a free electron (majority carrier).

The majority charge carriers in a p-type semiconductor are:

  1. Electrons
  2. Holes
  3. Protons
  4. Ions

Answer: B

Trivalent impurities create holes, which become the majority carriers.

A p–n junction diode conducts easily when it is:

  1. Reverse biased
  2. Forward biased
  3. Unbiased
  4. Heated to melting

Answer: B

Forward bias narrows the depletion region and allows current to flow.

Hooke’s law states that, within the elastic limit:

  1. Stress is proportional to strain
  2. Stress is inversely proportional to strain
  3. Strain is constant
  4. Force is proportional to area

Answer: A

The constant of proportionality is the modulus of elasticity.

The SI unit of Young’s modulus is:

  1. N m
  2. N m⁻² (pascal)
  3. No unit
  4. J

Answer: B

It is stress ÷ strain, and strain has no unit.

A material that breaks soon after its elastic limit, with little plastic deformation, is:

  1. Ductile
  2. Brittle
  3. Elastic
  4. Plastic

Answer: B

Glass is a typical brittle material.

Insulators have:

  1. No energy gap
  2. A very small energy gap
  3. A large energy gap between valence and conduction bands
  4. Overlapping bands

Answer: C

Electrons cannot easily jump into the conduction band.

A bipolar transistor has three terminals called:

  1. Anode, cathode and grid
  2. Emitter, base and collector
  3. Source, gate and drain only
  4. Positive, negative and earth

Answer: B

A small base current controls a larger collector current.

A rectifier converts:

  1. DC into AC
  2. AC into DC
  3. Low voltage into high voltage
  4. Light into electricity

Answer: B

Diodes are used to allow current in one direction only.

Below its critical temperature, a superconductor has:

  1. Very high resistance
  2. Zero resistance
  3. Negative resistance
  4. Variable resistance

Answer: B

Current can flow without any energy loss.

An LED gives out light when it is:

  1. Reverse biased
  2. Forward biased
  3. Unbiased
  4. Heated strongly

Answer: B

Electrons and holes recombine and release energy as photons.

Crystalline solids, unlike amorphous ones, have:

  1. No definite shape
  2. A sharp, definite melting point
  3. No order
  4. Only metallic bonds

Answer: B

Amorphous solids soften gradually.

Strain has:

  1. Units of N m⁻²
  2. No units
  3. Units of metres
  4. Units of newtons

Answer: B

Strain is a ratio of change in length to original length.

If a wire is stretched beyond its elastic limit, it:

  1. Returns exactly to its original length
  2. Is permanently deformed
  3. Becomes a semiconductor
  4. Loses all mass

Answer: B

Beyond the elastic limit, plastic deformation occurs.

The depletion region of a p–n junction contains:

  1. Many free electrons
  2. Very few free charge carriers
  3. Only holes
  4. Only protons

Answer: B

Carriers have recombined near the junction.

A Zener diode is commonly used as a:

  1. Light source
  2. Voltage regulator
  3. Amplifier
  4. Capacitor

Answer: B

It maintains a nearly constant voltage in reverse breakdown.

Which logic gate gives an output of 1 only when all inputs are 1?

  1. OR
  2. AND
  3. NOT
  4. NOR

Answer: B

AND requires every input to be high.

Which two gates are called universal gates?

  1. AND and OR
  2. NAND and NOR
  3. NOT and XOR
  4. XOR and XNOR

Answer: B

Any logic circuit can be built from NAND gates alone or NOR gates alone.

A transistor can be used as a(n):

  1. Amplifier or switch
  2. Battery
  3. Fuse
  4. Transformer

Answer: A

A small base current controls a larger collector current.

PMC Practice Test A half-wave rectifier operates from 50 Hz mains. The fundamental frequency of the ripple will be:

  1. 100 Hz
  2. 25 Hz
  3. 200 Hz
  4. 50 Hz

Answer: D

PMC Practice Test Non-inverting amplifier circuits have:

  1. A very high input impedance
  2. A very low input impedance
  3. A low output impedance
  4. None of the above

Answer: A

PMC Practice Test Which of the following rectifier uses wheatstone bridge to rectify signal

  1. Half wave
  2. Full wave
  3. Bridge
  4. All of the above

Answer: C

PMC Practice Test If the peak voltage across a full-wave rectifier is 20 V, the rms voltage is:

  1. 7.07 V
  2. 14.14 V
  3. 16.8 V
  4. 12 V

Answer: B

PMC Practice Test In a full-wave rectifier with an input frequency of 50 Hz, the ripple in the output is mainly of frequency:

  1. 25 Hz
  2. 50Hz
  3. 100Hz
  4. Zero

Answer: C

PMC Practice Test Half wave rectifier passes only

  1. Lower half cycle
  2. Upper half cycle
  3. Both cycles
  4. None of them

Answer: B

PMC Practice Test The output voltage of a rectifier is

  1. Smooth
  2. Pulsating
  3. Perfectly direct
  4. Alternating

Answer: B

PMC Practice Test A full wave rectifier passes into positive cycles

  1. Lower half cycle
  2. Upper half cycle
  3. Both cycles
  4. None ofthem

Answer: C

PMC Practice Test Which of the following is a type of rectifier

  1. Half wave
  2. Full wave
  3. Bridge
  4. All of the above

Answer: D

PMC Practice Test In half-wave rectification, during the negative half-cycle the diode is:

  1. Reversed biased
  2. Forward biased
  3. Potential barrier
  4. None of these

Answer: A

PMC Practice Test A bridge rectifier is preferred to an ordinary two-diode full-wave rectifier because:

  1. It needs much smaller transformer for the same output
  2. No center tap required
  3. Less PIV rating per diode
  4. All of the above

Answer: D

PMC Practice Test In a centre-tap full-wave rectifier, if Vm is the peak voltage across half the secondary, the maximum (peak inverse) voltage across a non-conducting diode is:

  1. Vm
  2. Vm/√2
  3. 2Vm
  4. Vm/3

Answer: C

PMC Practice Test A full-wave rectifier operates from 50 Hz mains. The fundamental frequency of the ripple will be:

  1. 100 Hz
  2. 25Hz
  3. 50Hz
  4. 200Hz

Answer: A

PMC Practice Test The process of converting altemating current to direct currentis called

  1. Modulation
  2. Amplification
  3. Oscillation
  4. Rectification

Answer: D

PMC Practice Test Substances attracted (weakly) by a strong applied magnetic field are called:

  1. Diamagnetic
  2. Paramagnetic
  3. Good conductor
  4. Ferromagnetic

Answer: B

PMC Practice Test The maximum efficiency of a half-wave rectifier is:

  1. 80.6 %
  2. 40.60%
  3. 70%
  4. 50%

Answer: B

PMC Practice Test A half-wave rectifier uses:

  1. One diode
  2. Two diode
  3. Three diodes
  4. Four diodes

Answer: A

PMC Practice Test Which of the following is not a type of rectifier?

  1. Phase wave rectifier
  2. Full wave
  3. Half wave
  4. None of them

Answer: A

PMC Practice Test The basic purpose of a filter (in a rectifier circuit) is to:

  1. Minimize variation in ac signal
  2. Suppress harmonics in rectified output
  3. Remove ripples from the rectified output
  4. Stabilize dc output voltage

Answer: C

PMC Practice Test In half-wave rectification, the DC output is obtained across the load during:

  1. The positive half cycle of input AC
  2. The negative half cycle of input AC
  3. The positive and negative half cycles of input AC
  4. Either positive or negative half cycle of input AC

Answer: D

PMC Practice Test A capacitor filter in a rectifier circuit performs satisfactorily only when the load:

  1. Current is high
  2. Current is low
  3. Voltage is high
  4. Voltage is low

Answer: B

PMC Practice Test The average DC voltage across the load of a full-wave rectifier, in terms of Vmax, is:

  1. 0.532 Vmax
  2. 0.637Vmax
  3. 0.759Vmax
  4. 0.437Vmax

Answer: B

PMC Practice Test A half-wave rectifier uses how many diodes?

  1. 1
  2. 2
  3. 3
  4. 4

Answer: A

PMC Practice Test Which one of the following is a photoconductor?

  1. Silver
  2. Gold
  3. Selenium
  4. Mercury

Answer: C

PMC Practice Test A full-wave (centre-tap) rectifier uses:

  1. One diode
  2. Two diode
  3. Three diodes
  4. Four diodes

Answer: B

PMC Practice Test In a rectifier, larger the value of shunt capacitor filter

  1. Larger the peak-to-peak value of ripple voltage
  2. Larger the peak current in the rectifying diode
  3. Longer the time that current pulse flows through the diode
  4. Smaller the dc voltage across the load

Answer: C

PMC Practice Test A diode works in bias for rectification

  1. Forward
  2. Reverse
  3. Mid
  4. Positive

Answer: A

PMC Practice Test A circuit that adds positive or negative dc voltage to an input sine wave is called

  1. Clamper
  2. Clipper
  3. Diode clamp
  4. Limiter

Answer: A

PMC Practice Test Materials that have both metallic and non-metallic characteristics are called

  1. Semiconductor
  2. Metal
  3. Non metal
  4. Organic compound

Answer: A

PMC Practice Test Which of the following are component of half wave rectifier

  1. Transformer
  2. Load resistance
  3. Power supply
  4. All of the above

Answer: D

PMC Practice Test The ripple factor of a half-wave rectifier is:

  1. 1.21
  2. 0.8
  3. 0.6
  4. 0.4

Answer: A

PMC Practice Test Ripple factor is defined as:

  1. Irms/Vrms
  2. Idc/Irms
  3. Irms/Idc
  4. Irms + Idc

Answer: C

PMC Practice Test In a half wave rectification, the diode conducts during

  1. Both half cycles
  2. Positive half
  3. Negative half
  4. None of these

Answer: B

PMC Practice Test If the line frequency is 50 Hz, the output frequency of a bridge rectifier is:

  1. 50 Hz
  2. 100 Hz
  3. 200 Hz
  4. 150 Hz

Answer: B

PMC Practice Test The number of diodes in bridge rectifier is

  1. 4
  2. 3
  3. 2
  4. 5

Answer: A

PMC Practice Test Rectifier is a device which converts

  1. AC to DC
  2. DC to AC
  3. AC to triangular current
  4. DC to triangular current

Answer: A

PMC Practice Test In a full-wave rectifier with 50 Hz input, the ripple in the output is mainly of frequency:

  1. 25 Hz
  2. 50 Hz
  3. 100 Hz
  4. Zero

Answer: C

PMC Practice Test If a half-wave rectifier converts 50 Hz AC into DC, the number of pulses per second in the output is:

  1. 25
  2. 50
  3. 100
  4. 75

Answer: B

PMC Practice Test In which rectifier is the ripple factor smaller?

  1. Full wave
  2. Half wave
  3. Both a) and b)
  4. None of them

Answer: A

Young's modulus is the ratio of:

  1. Tensile stress to tensile strain
  2. Force to area
  3. Strain to stress
  4. Extension to original length

Answer: A

Y = stress/strain within the elastic limit.

The SI unit of stress is:

  1. N m⁻² (pascal)
  2. N
  3. N m
  4. It has no unit

Answer: A

Stress = force/area.

Strain:

  1. Is measured in N m⁻²
  2. Is measured in metres
  3. Has no unit
  4. Is measured in newtons

Answer: C

Strain is a ratio of two lengths, so it is dimensionless.

Hooke's law holds up to the:

  1. Breaking point
  2. Yield point
  3. Plastic region
  4. Proportional limit

Answer: D

Beyond the proportional limit, stress is no longer proportional to strain.

Materials that break soon after the elastic limit are called:

  1. Ductile
  2. Plastic
  3. Malleable
  4. Brittle

Answer: D

Glass and cast iron are brittle.

In a p-type semiconductor, the majority charge carriers are:

  1. Neutrons
  2. Protons
  3. Holes
  4. Electrons

Answer: C

Trivalent impurities create holes.

Doping silicon with phosphorus (a pentavalent impurity) produces a/an:

  1. p-type semiconductor
  2. Superconductor
  3. n-type semiconductor
  4. Insulator

Answer: C

The fifth valence electron of each phosphorus atom becomes a free electron.

A p-n junction diode conducts significant current when it is:

  1. Reverse biased
  2. Unbiased
  3. Cooled to 0 K
  4. Forward biased

Answer: D

Forward bias reduces the depletion region and the potential barrier.

A diode is mainly used as a:

  1. Rectifier
  2. Transformer
  3. Capacitor
  4. Amplifier

Answer: A

It allows current in one direction only, converting AC to DC.

The energy gap between the valence and conduction bands of an insulator is:

  1. Negative
  2. Zero
  3. Large (more than about 5 eV)
  4. Small (about 1 eV)

Answer: C

Electrons cannot easily jump the large gap, so insulators do not conduct.

A bipolar junction transistor has:

  1. One p-n junction
  2. No junction
  3. Three p-n junctions
  4. Two p-n junctions

Answer: D

It has emitter–base and base–collector junctions.

The output of a NOT gate is 1 when its input is:

  1. 0
  2. Both 0 and 1
  3. 1
  4. Neither

Answer: A

A NOT gate inverts its input.

An AND gate gives an output of 1 only when:

  1. All inputs are 1
  2. All inputs are 0
  3. Any input is 1
  4. One input is 0

Answer: A

Y = A·B.

Below their critical temperature, superconductors have:

  1. Zero resistance
  2. Negative resistance
  3. Very high resistance
  4. Infinite resistance

Answer: A

Current can flow without any energy loss.

The property of a material that allows it to be drawn into wires is:

  1. Elasticity
  2. Brittleness
  3. Ductility
  4. Hardness

Answer: C

Copper is highly ductile.

Contact Form